| Corporate offices In Ft. Worth, TX 1-800-827-0711 www.texasrefinery.com |
Independent Sales Contractor Michael Bialecki Selling the products of Texas Refinery Corp. Click here to email me directly. |
To contact me please call 410-858-8290 or Fax 1-866-259-6187 |
| Home | Products | Trc History |
|
|
|
| Texas Refinery Corp. has always had good products for hydraulic systems, but continuous research and development has improved things once again. New generation base stocks and powerful additive systems in huge amounts make Texas Refinery HYDRAULIC OIL a high performance giant. In today's hydraulic systems, which operate under higher pressure and heat loads, there's a real need for superior hydraulic oils and the answer comes from Texas Refinery Corp.'s HYDRAULIC OILS. |
Reduces Costly Wear
HYDRAULIC OIL is a high quality, stable product formulated to provide excellent performance. Increased protection against surface wear is accomplished with the use of HYDRAULIC OIL- - it forms a film on metal surfaces, reducing metal to metal contact. Texas Refinery Corp. incorporates more zinc (an anti-wear additive) into its hydraulic oil, than is required on most equipment specifications - - an extra step to prolong the life of equipment. Reducing friction wear often reduces operating temperatures and that in turn helps increase the life of the oil and the equipment.
Resists Chemical Breakdowns
Hydraulic oils are subjected to many problem-causing factors . . . high temperatures, water, air, and foreign debris. This combination leads to oxidation, producing sludge, varnish, acids, and eventually a thick, gummy material in the oil. To prevent this, Texas Refinery Corp. manufactures HYDRAULIC OIL from new generation base oils which have a high stability and then TRC boosts the stability even further with extra portions of powerful anti-oxidation additives. In an oxidation test, HYDRAULIC OIL performed satisfactorily for over 10,000 hours, in most grades - - better than five times the taget normally sought.
Protects Seals
A hydraulic piston operates under high pressure, requiring a lubricant which reduces friction of the seal material, without damage to the seal itself. Formulated to protect seals. Friction is reduced and longer service life is obtained. This savings is accomplished by high-quality materials used in Texas Refinery Corp.'s HYDRAULIC OIL formulation.
Resists Foaming
For peak efficiency, hydraulic systems must use an uncontaminated oil as an operating medium. Water contamination, among other things, causes foaming, especially where elevated temperatures are encountered. Also, air entrapped in the system can cause a foaming problem. Texas Refinery Corp.'s HYDRAULIC OIL contains special anti-foam chemistry in large amounts, so the fluid releases any air or water that may be causing the foam. Reducing foam also decreases heat, and improves the life of the oil and the equipment.
Protects Against Rust
If an oil is formulated properly, metals should not rust, even if moisture is present. HYDRAULIC OIL has the special additives in large quantities to protect metal surfaces from rust. The film forming chemistry, coats all metal surfaces with a thin film, preventing moisture and other rust promoters from reaching the surfaces. With the use of HYDRAULIC OIL, the worries of rust are over.
Dependable
An inferior hydraulic oil becomes thick when cold and can cause a pump to cavitate. When weather is hot, the oil becomes thin, causing a loss around seals. The thin oil also tends to accelerate wear and give other problems. HYDRAULIC OIL shows very little change in its flow characteristics through its service life. The better quality base oils and superior additives in large quantities helps HYDRAULIC OIL maintain its viscosity and performance - - for dependability!
| Product Code |
|
|
|
|
|
|
|
| ISO Grade |
|
|
|
|
|
|
|
| Approx. SAE No. |
|
|
|
|
|
|
|
| API Gravity, ASTM D-28 |
|
|
|
|
|
|
|
| Flash Point, °F., COC, Min. ASTM D-92 |
|
|
|
|
|
|
|
| Fire Point, °F., COC, Min. ASTM D-92 |
|
|
|
|
|
|
|
| Pour Point, °F., (Max.) ASTM D-97 |
|
|
|
|
|
|
|
| Viscosity, SUS at 100°F. ASTM D-445 |
|
|
|
|
|
|
|
| Viscosity, SUS at 210°F. ASTM D-445 |
|
|
|
|
|
|
|
| Viscosity Index (Min.) ASTM D-2270 |
|
|
|
|
|
|
|
| Oxidation Test (hrs.) ASTM D-943 |
|
|
|
|
|
|
|
| Aniline Point, °F., ASTM D-1012 |
|
|
|
|
|
|
|
| Rust Test, ASTM D-665 |
|
|
|
|
|
|
|
| Sulfated Ash, Wt. % ASTM D-874 |
|
|
|
|
|
|
|
| Timken OK Load, Lbs. (Min.) |
|
|
|
|
|
|
|
| Zinc, Wt. % (by A A) |
|
|
|
|
|
|
|
| Demulsibility (ASTM D-1401) |
|
|
|
|
|
|
|
| Cincinnati Lamb Approvals |
|
|
|
|
|
|
| Texas Refinery Corp. HYDRAULIC OIL also meets and exceeds Lee-Norse 100-1, Ford M6C32, DIN 51524-part 2, US Steel 136 and 127, Racine Variable Volume Vane Pumps, AFNOR NFE 48-690 (dry), AFNOR NFE 48-691 (wet), AFNOR NFE 48-603, Jeffrey No. 87, BF Goodrich 0152, General Motors LH-04-1, LH-06-1 and LH-15-1, Eaton-Vickers M-2950-S (Mobile Hydraulic Systems), Eaton-Vickers I-286-S (Industrial Hydraulic Systems), Denison HF-1, HF-2, HF-0. Other Commerical Hydraulics except for PM-500 Series silver containing pumps which require R & O additive systems. |
HYDRAULIC OIL meets all major pump manufacturers' specifications.