DESCRIPTION:

D-45 NF is a white, flowing powder. It is a blend of specially selected alkaline detergents, foam control agents, water softening agents and wetting agents. In use concentrations, D-45 NF has a pH of 11-12.


PURPOSE:

D-45 NF is designed to remove light to medium petroleum soils and animal fats. Its foam control agents, alkaline detergents and the fact that it can be safely used on aluminum and other non-ferrous metals, make it ideal for spray cabinet cleaning. Where low foam and aluminum safety are required, D-45 NF fills your needs. It can also be used for hot-vat cleaning.


DIRECTIONS FOR USE:

SPRAY CABINETS: Use at 1 to 4 ounces per gallon of water. For many operations, 2 ounces per gallon works best. Recommended solution temperatures is 160-200°F. "Sweeten" the cabinet as needed by addition of D-45 NF to replace that lost by drag-out and reaction with soil. How often a cabinet is "sweetened" and how much is added will vary from business to business.
HOT VATS: D-45 NF is recommended to be used at concentrations of from 4 to 6 ounces per gallon water. Temperatures should be maintained at or near the boiling point for cleaning ferrous metals. The addition of agitation by means of a rolling boil or air agitation is a distinct advantage in the cleaning operation. For cleaning aluminum or other non-ferrous metals, temperatures should be between 160 and 180°F.
GENERAL PURPOSE CLEANING: D-45 NF is recommended at concentrations of 1 to 4 ounces per gallon of hot or cold water.


ADVANTAGES:

1. Foam control agents make it ideal for spray cabinet cleaning and other procedures requiring foam free operation.
2. Contains high speed wetting action ingredients for quick penetration of soils.
3. Contains a high degree of water softening ingredients insuring no residue on rinsing. 4. Compounded to be safe on aluminum and other non-ferrous metals.
5. 100% soluble; 100% active; no fillers.
6. High soil dispersing ability insures longer solution life.
7. Easy to use. Just dissolve in water, heat and it's ready to clean.


CAUTION: EYE IRRITANT
Contains sodium metasilicate and sodium carbonate. Avoid contact with skin, eyes, or clothing. Avoid breathing dust or mist. DO NOT SWALLOW. When handling, wear face shield or goggles, rubber gloves and protective clothing. While mixing, add slowly to surface of water and avoid splattering. Always add to lukewarm water. Product generates heat on mixing and may cause boiling of hot water. Use with good ventilation. Eyewash fountains in the workplace are strongly recommended.

IF SWALLOWED: NEVER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON. DO NOT INDUCE VOMITING. Give large quantities of water. If available, give several glasses of milk. If vomiting occurs spontaneously, keep airway clear. SEEK MEDICAL ATTENTION IMMEDIATELY.

EYE CONTACT: Immediately flush with plenty of cold water for at least 15 minutes. CALL A DOCTOR IMMEDIATELY. Object is to flush material out immediately, THEN SEEK MEDICAL ATTENTION. Washing eyes within 1 minute is essential to achieve maximum effectiveness. Hold lids apart to ensure flushing of the entire surface.

SKIN CONTACT: Brush off excess. Immediately wash contaminated areas with plenty of water for 15 minutes. SEEK MEDICAL ATTENTION IMMEDIATELY FOR BURNS AND ANY SERIOUS EXPOSURE. If irritation persists on any type of exposure, see a doctor. DO NOT apply salves or ointments for 24 hours to affected areas unless directed by medical personnel.

INHALATION: Remove to fresh air. SEEK MEDICAL ATTENTION IMMEDIATELY.

FOR CONTAMINATED CLOTHING: Remove immediately and wash before re-use. Discard footwear which cannot be decontaminated.

CONTAINER DISPOSAL: Triple rinse (or equivalent). Then offer for recycling or reconditioning or dispose of in accordance with Federal, State and local regulations. Keep container closed when not in use. Store in cool, dry area away from acids. Wash thoroughly after handling or contact.

Consult MSDS for more detailed information on the safe handling of this product.

FOR COMMERCIAL OR INDUSTRIAL USE ONLY!

KEEP OUT OF THE REACH OF CHILDREN!


HOW TO MEASURE A VAT To measure a vat you will need to multiply its:
L(length) ft. x W(width) ft. x D*(depth) ft. x 7.48 = (gallons of working solution)

or

L(length) in. x W(width) in. x D(depth) in. _ 1728 x 7.48 = (gallons of working solution)
* To arrive at the proper depth measurement, you must measure from the top of the working solution inside the vat to the bottom of the vat, NOT from the top of the vat itself. DO NOT put tape measure inside of vat. MEASURE FROM
THE OUTSIDE ONLY.
TO DETERMINE THE AMOUNT OF VAT PRODUCT THE CUSTOMER WILL NEED Gallons of Working Solution x Recommended Product Concentration = Product Quantity
For Example:    Recommended product concentration is 1 pound per gallon solution: Vat measurement: 5 x 3 x 2 = 224.40 gallons x 1 = 225 pounds of product
Recommended product concentration is 1'/ pounds per gallon of solution: Vat measurement: 5 x 3 x 2 - 224.40 gallons x 1.5 = 338 pounds of product


Warranty and Liability Disclaimer
The above information and recommendations concerning this product are based upon laboratory tests and field use experience; however, since conditions of actual use are beyond our control, any recommendations are made without warranty, expressed or implied. Manufacturer's and seller's sole obligation shall be to replace the portion of the product shown to be defective. Neither shall be liable for any loss, damage or injury, direct or consequential, arising out of the use of this product.